For additional specifications on this rig, please download the technical data sheet.
- (2) 3-1/8″ 5000# & (4) 2-1/16″ 5000# Gate Valves
- (2) 5″ x 6″ Charge Pumps, Ea p/b 75HP Elec Motor, Skidded
- (2) Adj Chokes, Skidded
- (2) Air-Actuated Charge Pumps, Skidded
- (2) NATIONAL 8-P-80 Triplex Pumps w/SOUTHWEST Forged Steel Fluid End
- (3) 5″ x 6″ Cent Pumps, Ea p/b 75HP Elec Motor
- (3) Sets 40″H Triangular Pipe Racks
- (4) 6-1/4″OD Drill Collars (Covered in Pipe Box)
- (4) 8’W x 40″H x 36’L Pipe Tubs
- (4) Leveling Jacks 117’H 400,000 lbs SHL Telescoping Mast
- 10’W x 8’H x 30’L Crimped Steel Mud Tank w/(2) 8’L Covered Porches
- 10’W x 8’H x 45’L Crimped Steel Mud Tank w/6’L Covered Porch
- 11″ 5000# Dbl BOP w/Rams
- 250-Ton 5-Sheave Block/Hook Combo IDECO 16’H x 20’6″W x 24’L Telescoping Substructure
- 27-1/2″ Rotary Table
- 4′ x 5′ Linear Motion Shale Shaker
- 4’H x 50’L Back-On Ramp
- 42″H x 5’6″W x 52’L Catwalk
- 5000# Choke Manifold w/4-Way Cross
- 6-Sheave Crown Block
- 8’W x 20’L Container, Skidded w/Contents
- 8’W x 40’L Container, Skidded w/Contents
- 8’W x 40″H x 34’L Junk Box w/Contents
- 9’8″W x 10’H x 30’L 500-Bbl Crimped Steel Water Tank w/Built-In Stairs
- 9’Dia x 21’L 10,000-Gal Self-Contained Fuel Tank, Skidded
- 9’W x 30’L Crimped Steel Doghouse w/6’L Porch, Skidded
- 9’W x 38’L Crimped Steel Gen House w/CUTLER HAMMER Switchgear
- Chain Drive Assembly
- Changeover Sub & Misc
- Covered Master Skids (No Power)
- Drill Line
- Drill Pipe
- DS 4-Station 80-Gal Closing Unit w/Rotary Charge Pump
- Elevator Links
- Elevator Slips f/4-1/2
- Grooved f/1-1/8″ Line
- HPU p/b CAT C-15 Diesel Eng, Skidded
- HYDRIL K-20-5000 Pulsation Dampeners
- IDECO 200-Ton Tru-Line Swivel w/Kelly, I-R Air Hoist
- Mtd on IDECO Back-In Rambler 6-Axle Carrier p/b (2) CAT C-15 Diesel Engs, Ea w/ALLISON 5860 Trans
- OILWORKS 1600 Wireline Measuring Device, Skidded
- PARMAC V-80 Brake
- Parts Room
- QUINCY 350 Air Compressor p/b 20HP Elec Motor
- Racking Board
- Type B Tongs
